|ขนาดสินค้ารวมบรรจุภัณฑ์||(W x L x H) 10 x 20 x 10 cm|
ชื่อแบรนด์ : Thermaltake
รุ่น : C1000 White 1000ml
ขนาดสินค้า : 10 x 20 x 10 cm
น้ำหนักสินค้า : 1 kg
การรับประกัน : 1 Year (นับจากวันที่ซื้อสินค้า) /รับประกันภายในประเทศ
Thermaltake C1000 Opaque Coolant White
The latest C1000 Opaque Coolant launched by Thermaltake is used as anti-corrosion protection fluid and heat-transfer medium for PC water-cooling. Made in Germany, the C1000 Opaque coolant is virtually odorless, non-flammable, and high performance liquid, offering superb protection for copper, nickel, brass, and aluminum. Choose from seven vivid colors: red, green, blue, orange, yellow, white, and purple to brighten up any build with Thermaltake.
German-Made Anti-Corrosive Solution
Being non-flammable, the C1000 Opaque Coolant is a ready-to-use cooling solution with at least 3 years shelf life in airtight containers, providing great performance while preventing the entire cooling system – copper, brass, nickel, and aluminum – from corrosion.
*MSDS: Material Safety Data Sheet
The C1000 Opaque Coolant is classified in water hazard class 1 (low-rate endangering) according to German water hazard regulations. The product is readily biodegradable.
Thermaltake C1000 Opaque Coolant is designed specifically for PC liquid cooling systems. Featuring anti-freezing, anti-rusting, water scale prevention and easy application, the C1000 non-transparent coolant brings vivid colors into your build and delivers great thermal efficiency and further reduce the temperature of the system.
1.The coolant color may change over time.
2.The precipitations at the bottom of the bottle are considered normal.
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
Fill the reservoir to the top as it will prevent air from going into the pump
If necessary tilt the system slightly from side to side to bleed the air out of the loop.
Place some paper towels under fittings and joining points to test for leaks.
Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
Coolant might fade over time.
- 1000 ml
- Ethanediol Value < 20%
- CAS 170-21-1
- EG 203-473-3
- Index 603-027-00-1
- Certificate Xn
- R-Phrase 22
- S-Phrase 2, 24/25,46
* Specifications are subject to change without notice.
* The product picture(s) is only for your reference, it may differ from the actual product.
Call Center / ช่องทางการรับประกัน
433 ถนนสุคนธสวัสดิ์ แขวงลาดพร้าว เขตลาดพร้าว กรุงเทพฯ 10230
โทรศัพท์ + 66(0) 2553 - 8899 / แฟกซ์ + 66(0) 2578 - 8195