|Packaging Dimension||(W x L x H) 1.2 x 1.2 x 100 cm|
|Weight Detail||0.1 kg|
ชื่อแบรนด์ : Thermaltake
รุ่น : V-Tubler PETG Tube 12mm 4 Pack
ขนาดสินค้า : 1.2 x 1.2 x 100 cm
น้ำหนักสินค้า : 0.1 kg
การรับประกัน : 1 Year (นับจากวันที่ซื้อสินค้า) /รับประกันภายในประเทศ
Thermaltake V-Tubler PETG Tube 12mm OD 10mm ID 1000mm 4 Pack
Thermaltake introduces the V-Tubler PETG solid tubing for custom PC water cooling configurations. Manufactured from premium PETG, the V-Tubler rigid tubing allows users to route the tubes runs exactly to their heart’s content. Designed with 12mm OD PETG tube adapter fittings, it gives users better mounting, easier fitting, and ideal flow to make your system a showcase for all to see.
100% PETG Material
100% PETG Material Made in Taiwan, the V-Tubler PETG Tube is constructed from superior PETG material which is reliable, non-toxic, and substance free. Thicker walls ensure safe operation, enabling the users to make the straightest run as well as tightest bends without the need of excessive compression fittings and 90 degree angle rotaries. Working temperature ranges from -4℉ (-20℃) to 143.6℉ (62℃).
- Outer Diameter: 12 mm
- Inner Diameter: 10 mm
- Length: 1000mm*4
Designed for use with 12mm OD PETG tube adapter fittings, V-Tubler PETG Tube is pre cut into retail coils of four 1000mm lengths, allowing enthusiasts to build up aesthetically-superior water cooling systems by allocating the radiators to each particular component and incorporating externally-modular upgrades for their chassis.
*Coolant operating temperature exceeds 50℃/122°F may potentially affect the PETG tube.
*Thermaltake V-Tubler PETG Tube Series is recommended for use with the Pacific Temperature Sensor.
Thermaltake recommends the following steps to be taken after completing your water loop setup
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
Fill the reservoir to the top as it will prevent air from going into the pump
If necessary tilt the system slightly from side to side to bleed the air out of the loop.
Place some paper towels under fittings and joining points to test for leaks.
Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
Coolant might fade over time.
- 10 mm
- 12 mm
- 1000 mm *4
* Specifications are subject to change without notice.
* The product picture(s) is only for your reference, it may differ from the actual product.
Call Center / ช่องทางการรับประกัน
433 ถนนสุคนธสวัสดิ์ แขวงลาดพร้าว เขตลาดพร้าว กรุงเทพฯ 10230
โทรศัพท์ + 66(0) 2553 - 8899 / แฟกซ์ + 66(0) 2578 - 8195